Sim card are the basis nedded of the people and everybody uses the phone minimum so traffic are going good but something knowledge is necessary to understand some techniques are also helpful us hello friends i am very happy to put my next article against you and thanking you for your fabulous support i wanted to tell you about the Sim card reader as below Once the reader design is built, the open source software can be used to read from and write to the card. Together they can be used to backup/restore stored SIM card data, recover deleted SMS's and phone contacts, examine the last phone numbers dialed, etc.
Nedded Tools are :
There are a few tools that are required for assembly. None of these tools are included. If you don't have them, now would be a good time to borrow or purchase them. They are very very handy whenever assembling/fixing/modifying electronic devices! I provide links to buy them, but of course, you should get them whereever is most convenient/inexpensive. Many of these parts are available in a place like Radio Shack or other (higher quality) DIY electronics stores.
Soldering iron. One with temperature control and a stand is best. A conical or small 'screwdriver' tip is good, almost all irons come with one of these.
A low quality (ahem, $10 model from radioshack) iron may cause more problems than its worth!
Do not use a "ColdHeat" soldering iron, they are not suitable for delicate electronics work and can damage the kit Check out my recommended basic soldering iron and where to buy.
Solder. Rosin core, 60/40. Good solder is a good thing. Bad solder leads to bridging and cold solder joints which can be tough to find. Don't buy a tiny amount, you'll run out when you least expect it. A half pound spool is a minimum.
Check out my recommended basic solder and where to buy.
Multimeter/Oscilloscope A meter is helpful to check voltages and continuity.
Flush/diagonal cutters. Essential for cutting leads close to the PCB.
Desoldering tool. If you are prone to incorrectly soldering parts.
Check out my recommended basic desoldering tool and where to buy.
'Handy Hands' with Magnifying Glass. Not absolutelynecessary but will make things go much much faster.
Check out my recommended basic 3rd hand tool and where to buy.
Its very interesting topic as you like
 | ||
| SIM CARD READER | By:www.moneystarts.blogspot.in |
Nedded Tools are :
There are a few tools that are required for assembly. None of these tools are included. If you don't have them, now would be a good time to borrow or purchase them. They are very very handy whenever assembling/fixing/modifying electronic devices! I provide links to buy them, but of course, you should get them whereever is most convenient/inexpensive. Many of these parts are available in a place like Radio Shack or other (higher quality) DIY electronics stores.
Soldering iron. One with temperature control and a stand is best. A conical or small 'screwdriver' tip is good, almost all irons come with one of these.
A low quality (ahem, $10 model from radioshack) iron may cause more problems than its worth!
Do not use a "ColdHeat" soldering iron, they are not suitable for delicate electronics work and can damage the kit
Solder. Rosin core, 60/40. Good solder is a good thing. Bad solder leads to bridging and cold solder joints which can be tough to find. Don't buy a tiny amount, you'll run out when you least expect it. A half pound spool is a minimum.
Check out my recommended basic solder and where to buy.
Multimeter/Oscilloscope A meter is helpful to check voltages and continuity.
Flush/diagonal cutters. Essential for cutting leads close to the PCB.
Desoldering tool. If you are prone to incorrectly soldering parts.
Check out my recommended basic desoldering tool and where to buy.
'Handy Hands' with Magnifying Glass. Not absolutelynecessary but will make things go much much faster.
Check out my recommended basic 3rd hand tool and where to buy.
Its very interesting topic as you like
No comments:
Post a Comment